TheWorkshopBlueprint logo THEWORKSHOPBLUEPRINTDIY BUILDING PLANS
← All plans

Wooden Tool Tote / Carpenter's Carrier Plan

Wooden Tool Tote / Carpenter's Carrier Plan plan cover
$9.95 Buy Now

Not a standard off-grid kit - top-of-the-line, above and beyond the old style - safer by design, and every claim below names a real feature drawn into the plan itself.

THE BUILD: an open wooden tool tote / carpenter's carrier, 24 in long x 12 in wide x 14 in tall, with a solid hardwood central handle, a 22-1/2 x 10-1/2 x 6-1/2 in interior (about 0.89 cubic feet), and an honest printed working limit of 40 lb of tools. This is NOT the rolling tool chest cabinet in this shop (a four-drawer cabinet on casters that stays in the workshop), NOT the wall-mounted pegboard tool cabinet (it hangs on studs and never leaves the wall), and NOT a workbench. It is the one-hand carrier you take to the job - and it is not a plastic bin or a nailed crate with a dowel stapled across the top.

A HANDLE THAT CANNOT PULL OUT - MATH TWO WAYS, THEN A PROOF TEST: the handle is a solid hardwood bar (1-1/2 in tall x 1 in thick) whose through-tenons pass completely through both 3/4 in plywood end panels, shoulders seated on the panels' inner faces, each tenon locked outside its panel by a 3/8 in hardwood tusk dowel bearing on the panel face, left 1/4 in proud so the lock can be inspected at a glance for the life of the tote. One screw per joint is used as a curing clamp only, and the plan says so plainly - no rated load rides on a screw. The strength math is printed in full and worked two ways: at the rounded-up 60 lb design lift (40 lb of tools plus the roughly 14 lb tote is 54 lb in real life), handle bending stress is about 900 psi against a conservative 9,000 psi hardwood figure - roughly a 10-to-1 margin by the harsh point-load method, about 20-to-1 by the spread-load method - and tenon bearing runs about 80 psi, roughly a 12-to-1 margin. Then the finished tote must physically pass a mandatory numbered proof step: loaded to 80 lb total on a scale, lifted by the handle, held 60 seconds while both joints are watched. Twice the tool allowance, about 1.5 times the worst legal lift.

A BOTTOM THAT CANNOT FALL OUT: the bottom panel does not hang from screws in its edges. It rests on a cleat ledge - standard 1x2 cleats laid flat on all four inside walls - a full 1-1/2 in of bearing width and 90 square inches of bearing area, computed two ways in the plan (panel-minus-middle ring method and strip-by-strip method agree at 90). The load path is panel down onto wood, all the way around.

EVERY NUMBER CHECKED TWO WAYS: length 3/4 + 22-1/2 + 3/4 = 24 in against the side board's own 24 in; width 3/4 + 10-1/2 + 3/4 = 12 in against the bottom panel fitting the same gap; height 8 + 6 = 14 in against the end panel's cut height; interior depth 6-1/2 in by subtraction and again by volume displacement; box squareness gated on equal diagonals (26-13/16 in) measured on the clamped box. Every screw in the plan has its pass-through and bite stated in a fastener table, and the three snug stacks (where a tip must stop 1/4 in short of a face) are proved on scrap in the practice stage before good wood is cut.

BEGINNER-FIRST, IN DEPTH: every term defined at first use (through-tenon, mortise, tusk dowel, bearing, bite, proof load, design load), a practice-first stage proving the mortise-and-tenon fit, the screw stacks, and the tusk lock on scrap, 28 continuously numbered steps in 7 stages, 12 labelled diagrams placed at their steps, a stop-and-check gate after every stage, mistake fixes (loose or belled mortise, off-datum layout, short tenon, dimpled screw tip, rocking bottom panel, out-of-square box, loose tusk dowel, biting grip, failed proof test), good/better materials (pine and BCX plywood vs Baltic-birch-style panels and hickory handle - with the honest note that only the handle stock and end panels gain from upgrading), and sourcing with exactly what to order, including the yield math (both sides from one 6 ft 1x10; both end panels and the bottom nested on one 24 x 48 in panel using 24-1/2 of its 48 in; all four cleats from one 6 ft 1x2, used flat with no ripping), costs labelled estimates totalling $55-$95 good / $85-$140 better.

You receive: the PDF plan only (digital download, no physical product ships) with cut list, materials list, full two-way verification section, and final completion checklist. Full build plans and material list in the TheWorkshopBlueprint website store at theworkshopblueprint.shop.

Finished size 24 in long x 12 in wide x 14 in tall; handle top 13-1/2 in; grip clearance 4 in above the 8 in rim; interior 22-1/2 x 10-1/2 x 6-1/2 in (about 0.89 cu ft); empty weight about 14 lb; printed tool limit 40 lb
Materials estimate $55-$95 good build / $85-$140 better build (estimate: 1x10 pine board, 24 x 48 in 3/4 in plywood panel, 1x2 pine board, hardwood handle stock, dowel rod, screws, glue, finish)
Skill level Beginner

See more plans in Workshop & Storage