TheWorkshopBlueprint logo THEWORKSHOPBLUEPRINTDIY BUILDING PLANS
← All plans

Wooden Adjustable-Height Standing Desk Plan - Pin-Adjustable Legs, 29 to 45 in

Wooden Adjustable-Height Standing Desk Plan - Pin-Adjustable Legs, 29 to 45 in plan cover
$14.95 Buy Now

Not a standard off-grid kit - top-of-the-line, above and beyond the old style - safer by design, and every claim below names a real feature drawn into the plan itself.

THE BUILD: a wooden adjustable-height standing desk with a 48 x 29 in desktop, manual pin adjustment from 29 in (sitting) to 45 in (standing) in 2 in steps - 9 working heights - set by hand with through-bolt pins. No motor and no electronics anywhere in the design; the plan says so plainly and claims no motorised performance.

SAFER BY DESIGN - THE DESK FAILURES ARE DESIGNED AGAINST: (1) TIPPING AT FULL HEIGHT is answered with 32 in feet that stand 1-1/2 in beyond the desktop edge on each side, and the tip math is printed in full: restoring moment 2,960 in-lb, about a 66 lb horizontal shove at the top edge to tip the loaded desk at 45 in - with the unloaded figure (about 30 lb) stated honestly beside it. A straight-down lean on the front edge lands inside the footprint and cannot tip the desk at all. (2) A RACKING ONE-PIN JOINT is answered with two bolts per leg, 6 in apart, through a lap that never falls below 10 in at any setting. (3) A DESKTOP CARRIED ON SCREWS is answered with full bearing: the panel rests on the complete apron rectangle and all four post tops, and screws only locate it. (4) PINCH POINTS AT THE ADJUSTMENT HOLES are named up front, with a two-person adjustment drill that keeps fingers out of the lap faces and holes.

STATED DESIGN LOAD: 100 lb evenly spread on the desktop, with the bearing path traced from panel to floor and the per-leg share worked in the plan (25 lb per leg joint, carried by two 3/8 in pins through 3 in of wood).

EVERY MEASUREMENT VERIFIED TWO WAYS: desktop width by board sum (4 x 7-1/4 = 29 in) and by frame span (25-1/2 + 1-3/4 + 1-3/4 = 29 in); desktop length by board cut (48 in) and by frame plus overhang (44 + 2 + 2 = 48 in); height range by hole spacing math (9 holes at 2 in centres span 16 in; 29 + 16 = 45 in) and by lap travel (column 42 - 26 = 16 in); restoring moment by total weight (185 x 16 = 2,960 in-lb) and by component sum (1,360 + 1,600 = 2,960 in-lb). Every fastener is reach-checked: the 4-1/2 in pin bolts pass the 3 in two-post path with 1-1/2 in left for washer, wing nut, and protruding thread.

BEGINNER-FIRST, IN DEPTH: every term defined at first use (lap joint, apron, bearing, bite, racking, restoring moment), a practice-first stage proving the pin joint and the two-bolt rule on scrap and sighting the tip geometry full-size on the floor, 33 continuously numbered steps in 6 stages, 12 labelled diagrams placed at their steps, a stop-and-check after every stage, mistake fixes (mismatched hole rows, a racking joint, a rocking desktop, sticking lap faces, a tippy feel at full height), a good/better materials path (hardwood desktop option, stainless pins for damp shops), and sourcing with all prices labelled ESTIMATE.

You receive: the PDF plan only (digital download, no physical product ships) with cut list, materials list, full two-way verification section, and final completion checklist. Full build plans and material list in the TheWorkshopBlueprint website store at theworkshopblueprint.shop.

Finished size Desktop 48 x 29 in; top height adjustable 29 to 45 in in 2 in steps (9 settings); feet 32 in front-to-back
Materials estimate $140-$210 (estimate: pine 2x8/2x4/2x6 lumber, 8 pin bolts with washers and wing nuts, screws, finish; better path with a hardwood desktop at the top of the range)
Skill level Beginner

See more plans in Furniture