TheWorkshopBlueprint logo THEWORKSHOPBLUEPRINTDIY BUILDING PLANS
← All plans

Quail Tractor Hutch Plan

Quail Tractor Hutch Plan plan cover
$11.95 Buy Now

Not a standard off-grid kit - top-of-the-line, above and beyond the old style - safer by design, and every claim below names a real feature drawn into the plan itself.

THE BUILD: a movable bottomless ground pen (a tractor) for coturnix quail, interior ground area 96 x 36 in (24 sq ft), exterior 99 x 39 in, total height 15 in with a 12 in interior clear height, built from a 2x2 frame with 1/2 in hardware cloth on every surface. The top divides into three 32 in bays: a solid shade panel screwed down over one bay, a hinged egg-access lid over the middle bay, and a fixed wire bay. A hinged end door gives main access, a small service hatch on one side reaches the 48 in trough feeder and the gravity waterer so daily feed and water never open the main pen, two 8 in wheels at one end and a lift handle at the other make the daily move a one-person job, and a fold-down hardware cloth apron pins flat around the base when parked.

SAFER BY DESIGN - THE ENGINEERING IS PRINTED IN THE PLAN: (1) PREDATION DESIGNED AGAINST WITH THE RIGHT WIRE - 1/2 in welded hardware cloth (19-gauge) on every side, bay, door, and apron, with an explicit ban on chicken wire and the reasons printed: raccoons tear the thin twisted hex wire, reach through its roughly 1 in openings, and small predators pass it, while the welded 1/2 in grid blocks paws and cannot unravel. Every cut wire edge is folded back 1/2 in before fastening. (2) CLEVER HANDS DESIGNED AGAINST - all three openings (egg lid, end door, service hatch) close with two-step latches: a barrel bolt plus a spring-loaded safety catch, or a hasp plus a carabiner clip, because a raccoon can learn one sliding motion and not two different motions, one spring-loaded. (3) DIG-IN AND THE FLOOR EDGE DESIGNED AGAINST - the bottom rails bear on the ground along their full length so the pen parks with no gap, every move ends with a printed flush check using a 1/2 in gauge block, and the 12 in hardware cloth apron folds down flat around the outside (long strips run 123 in so the corners are covered) so a digging predator hits wire at the wall and gives up. (4) HEAT DESIGNED AGAINST - a solid shade panel covers a full third of the pen (32 x 36 in, 8 sq ft, exactly the capacity density so all 15 birds can stand in shade at once), painted light on top to reflect sun, with wire on every other surface for ground-level airflow, a shade-to-afternoon-sun placement rule, and a midday water check in the printed daily routine. (5) BOING INJURY DESIGNED AGAINST, HONESTLY - the interior clear height is 12 in on purpose: a startled coturnix flushes vertically and a tall roof lets it reach killing speed, while at 12 in it reaches the wire before it has speed; the plan states plainly that this reduces the injury rather than eliminating it, and warns never to raise the roof to 18 or 24 in for reaching convenience - the egg lid and hatch exist so you never need to.

HONEST CAPACITY: usable floor is 23.5 sq ft after deducting the waterer footprint from the 24 sq ft interior (the wall-line trough strip is working floor birds stand in to feed). At 1.5 sq ft per coturnix that is 15.7 - round down: 15 maximum, and 12 comfortable at a generous 1.9 sq ft each. Checked the second way, the 48 in trough at 3 in of feeder edge per bird gives 16 feeding spaces - the feeder could serve 16, so the floor is the limit, and the plan rates the floor. A seller rating a 24 sq ft pen for 25 quail is rating cage density on grass.

EVERY MEASUREMENT VERIFIED TWO WAYS: floor area by feet (8 x 3 = 24 sq ft) and by inches (3,456 / 144); height by parts (1.5 + 12 + 1.5 = 15 in) and by clearance (12 + 3 = 15 in); bays by thirds (96 / 3 = 32 in) and by parts (32 + 32 + 32 = 96 in); hardware cloth by panels (11,013 sq in = 76.5 sq ft) and by rolls (body 49.5 sq ft from a 75 sq ft roll, apron 27.0 sq ft from a 50 sq ft roll); apron area by strips (3,888 sq in) and by outer-minus-inner rectangles (7,749 - 3,861 = 3,888 sq in); weight two ways bracketing 82-85 lb (parts sum and volume/share method), with the handle lift at about half the pen, roughly 40 lb; every fastener bite-checked (frame screws 1.5 in, door screws 1.25 in, shade screws about 1.1 in, hinge screws checked against frame thickness) and every load shown bearing on a dimensioned support - parked weight on the full-length bottom rails, axle bearing through both 2x4 wheel blocks, shade panel bearing on all four of its supports.

ONE-PERSON DAILY MOVE, SPECIFIED NOT PROMISED: the axle sits 4-1/2 in above the rail bottoms, so the 8 in wheels stand 1/2 in clear of the ground when parked - parked weight is on the rails with no floor gap and no rolling - and lifting the handle tips the pen onto its wheels with the wheel-end rail clearing about 2 in. The printed routine moves the pen one length each morning with the apron folded up, then folds it down, pins it, and runs the flush check at the new spot.

BEGINNER-FIRST, IN DEPTH: every term defined at first use (tractor, coturnix, covey, hardware cloth, apron, boing, interior clear height, bearing, bite, bay, barrel bolt, on center), a practice-first stage proving the frame corner joint and its bite, a folded glove-safe wire edge, and the two-step latch on scrap, 24 continuously numbered steps in 5 stages, 12 labeled diagrams placed at their steps, a stop-and-check after every stage, mistake fixes (floor-edge gaps, lid-startle flushing, skipped second latch steps, billowing wire, parked rolling, midday panting, fouled feed, predator sign at the apron), good/better materials (pine vs cedar frame, 19-gauge vs 16-gauge or coated mesh, plywood vs polycarbonate shade, stainless fasteners), and sourcing with exactly what to order - including both hardware cloth rolls specified by mesh and gauge - with costs labeled estimates totaling $209-$311.

You receive: the PDF plan only (digital download, no physical product ships) with cut list, materials list, full two-way verification section, daily-move routine, and final checklist. Full build plans and material list in the TheWorkshopBlueprint website store at theworkshopblueprint.shop.

Finished size Interior ground area 96 x 36 in (24 sq ft), exterior 99 x 39 in, total height 15 in with 12 in interior clear height; capacity 15 coturnix quail maximum (12 comfortable); total weight about 85 lb with about a 40 lb handle lift
Materials estimate $209-$311 (estimate: pine or cedar 2x2/1x2 frame, two rolls of 1/2 in hardware cloth, exterior plywood shade panel, 8 in wheels and axle, hinges and two-step latches, trough feeder and gravity waterer, exterior fasteners)
Skill level Beginner

See more plans in Coops & Animal