TheWorkshopBlueprint logo THEWORKSHOPBLUEPRINTDIY BUILDING PLANS
← All plans

Queen Murphy Wall Bed Plan

Queen Murphy Wall Bed Plan plan cover
$19.95 Buy Now

Build a queen Murphy wall bed that folds down from a floor-standing cabinet 66-1/2 in wide x 89 in high x only 17 in deep. Open, the queen mattress (60 x 80 in, 9-11 in thick) rests on a plywood bed panel that bears ON support cleats screwed to deep 15 in side rails - real bearing, about 212 sq in of it - carried at the head by a commercial, manufacturer-rated queen Murphy mechanism kit and at the foot by two folding, locking legs. Closed, the bed stands vertical in the cabinet, locked by two top safety locks, with the folded legs flush in the front inset.

This plan is honest about the safety case, in writing, before you cut anything. The moving weight is computed two independent ways and they agree: about 330 lb with a 100 lb design mattress (bed box about 230 lb). The pivot gravity moment is also computed two ways: 9,242 in-lb by segment sum and 9,240 in-lb by total weight x center-of-mass distance. Open-bed reactions are checked two ways as well (legs 333 lb total, pivot 397 lb total at the 730 lb design load of bed plus 400 lb of occupants). Because of those numbers, the plan requires a mechanism kit rated for your real moving weight with struts selected from the maker's chart - never generic gas struts and never a bolt-only DIY pivot - and it requires the cabinet to be lagged into at least four wall studs on two mounting rails, 16 lags minimum, each 5/16 x 4 in lag bite-checked at 2 in into the stud. Every other fastener is bite-checked too, and every structural connection (pivots, leg brackets, handles) is a through-bolt, never a screw.

Beginner-first, like every plan in this shop: every term defined at first use (stud, bite, bearing, pivot, gas strut, counterbalance, center of mass), a practice-first stage on scrap (lag joint, through-bolt, cleat bearing, folding-leg pinch point), 36 continuously numbered steps, a labeled diagram at every stage (12 illustrations), a stop-and-check checkpoint after each stage, mistake fixes for every stage, and a final checklist. All dimension chains are summed and shown two ways: width 3/4 + 62 + 3/4 = 63-1/2 in, length 3/4 + 80-3/4 + 3/4 = 82-1/4 in, closed stack 5 + 82-1/4 + 1 + 3/4 = 89 in, depth 1-1/4 + 15 + 3/4 = 17 in. Leg length (9 in reach), leg swing clearance, foot swing arc, pivot pinch gaps, mattress retention by rails plus two straps, and a measured counterbalance test (10-35 lb hand force on a scale) and a 400 lb / one-hour load test are all covered. The plan also tells you when NOT to build: fewer than four studs, a kit chart that does not cover your weight, a mattress over 11 in thick, or no second adult to help - any one of those is a stop.

You receive: a PDF plan with cut list, materials list, tool list, 36 steps, 12 diagram figures, full measurement verification, mistake fixes, and a final checklist, plus a materials estimate of $950-$1,450 (mechanism kit and plywood dominate; mattress not included).

DIGITAL DOWNLOAD: this listing is for the PDF building plan only. No physical product, hardware, or mechanism kit will be shipped. Print it or build from a tablet in the shop.

Full build plans and material list in the TheWorkshopBlueprint Etsy shop.

Finished size Cabinet 66-1/2 in wide x 89 in high x 17 in deep; open bed box 63-1/2 in wide x 82-1/4 in long, platform top 10-1/2 in above floor, mattress top about 21-1/2 in; mattress queen 60 x 80 in, 9-11 in thick; closed foot end at 87-1/4 in with 1 in top clearance; occupant load limit 400 lb distributed
Materials estimate $950-$1,450 (5x 3/4in plywood 4x8ft sheets, 1x queen Murphy mechanism kit rated for 330 lb moving weight, 2x6 and 2x4 mounting rails, 16x 5/16x4in lag screws, through-bolts, brackets, straps, handles, locks, finish; mattress not included)
Skill level Beginner (two-person, safety-critical build)

See more plans in Furniture