TheWorkshopBlueprint logo THEWORKSHOPBLUEPRINTDIY BUILDING PLANS
← All plans

Murphy Mobile Workshop Plan

Murphy Mobile Workshop Plan plan cover
$12.95 Buy Now

Build a complete workshop on four locking casters: a 68 x 27-3/4 in rolling cabinet whose front worktop leaf folds down for work and up vertical to store, Murphy-bed style. Stored footprint is just 68 x 28-1/2 in; open, the leaf gives you a 51-3/4 in deep workbench at exactly 36 in high. The left bay parks a jobsite table saw on an adjustable platform you build from a worksheet in the plan (stack = 36.00 - 10.50 - your saw's feet-to-table height), so the saw's table finishes dead flush with the 36 in worktop - a worked example (16-1/2 in saw = 9.00 in stack) and the full compatibility range (12-23 in) are computed in the plan. The right bay carries a 26 in rotating turntable miter station on a 12 in heavy-duty lazy-susan bearing, locked by two steel index pins at 0 degrees (work) and 180 degrees (store) - pins drilled with the disc clamped as its own jig, so they actually drop in. Inside the folding leaf is a French-cleat panel for light hand tools (5 lb cap, zones dimensioned) that swings into the open bay mouths as the leaf closes.

This plan shows its math before it asks for your trust. The 36 in worktop chain is summed two ways (6-1/4 caster + 3-1/2 rail + 3/4 deck + 24-3/4 side + 3/4 slab). The cabinet weight is computed two independent ways - about 196 lb by parts, about 198 lb by volume - and the maximum rolling weight is capped at 413 lb (cabinet + table saw up to 55 lb + miter saw up to 42 lb + stored tools up to 120 lb), about 103 lb per caster against a 250 lb rating, a 2.42x margin. The leaf's 100 lb rating is backed by a worked tip-over calculation (resisting 4,502 in-lb vs overturning 2,700 in-lb, 1.67x margin) and a weighed 100 lb proof-load step in the build. Every fastener is bite-checked with poke-through ruled out - including the French-cleat liner strips that exist specifically so the cleat screws stop 1/4 in short of the worktop face - and every load path runs by bearing (deck ON rails, slab ON side/divider/cleat, shelf ON cleats), never by a screw hanging in shear.

Beginner-first, like every plan from this shop: every term defined at first use (leaf, bearing, bite, spacer stack, index pin, French cleat, center of mass), a practice-first stage on scrap (bite-test joint split open and inspected, pin jig, French cleat, hinge flush fit), 48 continuously numbered steps across six stages, a labeled diagram at every technique stage (15 illustrations), a stop-and-check checkpoint after each stage, mistake fixes for every stage, and a final checklist that ends with a limits card you screw inside the cabinet - ratings, tool caps, pin positions, and the annual inspection note, all on one card. Saw compatibility is stated up front and measured in Step 5 before you cut anything: table saw up to 32 in wide x 26 in deep, feet-to-table 12-23 in; miter saw base up to 25 x 25 in and 42 lb. The turntable's rotation sweep (35.4 in corner circle) is drawn and clearance-tested in the plan, including the 6 in wall gap for parking.

You receive: a PDF plan with cut list, materials list with sourcing notes, tool list, 48 steps, 15 diagram figures, full measurement verification (dimension chains, weight two ways, moments, fastener bite table, clearances), mistake fixes, and a final checklist, plus a materials estimate of $470-$580 (prices labeled estimates, US big-box/online, late October 2026; your two saws are not included - this workshop houses them).

DIGITAL DOWNLOAD: this listing is for the PDF building plan only. No physical product, hardware, or tools will be shipped. Print it or build from a tablet in the shop.

Full build plans and material list in the TheWorkshopBlueprint shop.

Finished size Cabinet 68 in wide x 27-3/4 in deep x 36 in high at the worktop (1727 x 705 x 914 mm); stored footprint 68 x 28-1/2 in; operating footprint 68 x 51-3/4 in with leaf down; left bay 33 in clear, right bay 32-3/4 in clear; turntable disc 26 in diameter, top about 38-3/4 in; stored height with a typical miter saw about 52-56 in
Materials estimate $470-$580 estimated (3x 3/4in plywood 4x8ft sheets, 1x 1/2in sheet, 5x 2x4x8ft, 72in piano hinge, 12in heavy-duty lazy-susan bearing rated 500lb+, 4x 5in locking casters rated 250lb each, draw latches, quick pins, index pins and bushings, screws and lags, 12-gauge power strip, glue/finish/shims; saws not included)
Skill level Beginner (two-person lifts at marked steps)

See more plans in Workshop & Storage