Greenhouse Propagation Bench Plan
Not a standard off-grid kit - top-of-the-line, above and beyond the old style - safer by design, and every claim below names a real feature drawn into the plan itself.
THE BUILD: a 6 ft greenhouse propagation bench, 72 x 30 x 36 in, with an open slatted top (18 cedar 1x4 slats with dimensioned 1/2 in drainage gaps) at counter height and a slatted lower shelf (17 slats, surface at 12-3/4 in, 19 in of clear height above it) for flats, pots, and mix. Top capacity is 9 standard 1020 flats (10 x 20 in), proved two ways in the plan - by layout (3 along the length by 3 across the depth, with a 12 in spare strip left for the watering can) and by area (2,160 sq in of top against 200 sq in per flat gives a ceiling of 10, and rigid flats pack to 9). HOW IT DIFFERS FROM ITS NEIGHBOURS IN THIS STORE: the potting bench with soil bin (48 x 24 in) is a dry-work bench with a mostly solid top, tool back, and pull-out soil bin for filling pots - no drainage top, no wet-load rating. The seed-starting grow stand (55 x 24 x 72 in) is an indoor three-tier stand with solid shelves and bought grow lights, rated 50 lb per shelf. This bench is the wet-work bench that lives inside the greenhouse: one draining tier where flats are watered in place, a heavy lower shelf, wet-service materials throughout, and a computed 150 lb top load.
SAFER BY DESIGN - THE WET-BENCH FAILURES ARE DESIGNED AGAINST: (1) NO RAIL HANGS ON END GRAIN - every top and lower rail end RESTS ON a support cleat screwed to the leg (8 cleats, 8 rail ends), so the load travels wood-on-wood; through-leg screws are clamps only, and a practice joint in the plan proves the bearing and the 1 in screw bite on scrap first. (2) THE WET LOAD IS COMPUTED, NOT GUESSED - a saturated 1020 flat weighs about 12 lb, so 9 flats are 108 lb of real working load; the top is designed for 150 lb distributed (42 lb of margin, about 1.4 times the full wet load), the lower shelf for 100 lb distributed with its rating written on the bench itself in the plan's steps, and each flat crosses 5 slats so no flat rides on fewer than five supports. (3) DRAINAGE IS A DIMENSION - the top gap math is worked two ways (18 slats x 3-1/2 in + 17 gaps x 1/2 in + 2 end margins x 1/4 in = 72 in; and by 4 in pitch count), set with proved 1/2 in spacer blocks, dry-laid and measured at 72 in before a screw is driven, and proved again in a watered drainage test before the bench enters service. (4) NO POISON BESIDE FOOD PLANTS - materials are western red cedar or redwood, or modern ground-contact-rated treated lumber on the budget path, and the plan bans CCA-treated wood and creosote (railroad ties) anywhere near food plants in its Safety First section, in plain words. (5) IT SITS LEVEL ON A REAL GREENHOUSE FLOOR - a full levelling stage (bedded pavers on soil or gravel so legs never stand in ground moisture, composite shims or stainless adjustable glides, length then depth then twist, in that order) closed by a one-hour proof load at about 108 lb on top and 80 lb on the shelf.
EVERY MEASUREMENT VERIFIED TWO WAYS: bench length by frame parts (1-1/2 + 69 + 1-1/2 = 72 in) and by the slat layout sum; slat bearing (1-1/2 in on each rail + 27 in clear span = the 30 in slat) against the 30 in footprint; height by stack (35-1/4 leg + 3/4 slat = 36 in) and by rail line; lower shelf layout (17 x 3-1/2 + 16 x 1/2 + 2 x 3/4 = 69 in between the legs); clear height (31-3/4 rail underside - 12-3/4 shelf = 19 in, stated honestly - flats and short pots fit, tall plants do not). Every fastener is reach-checked: cleat and rail screws #8 x 2-1/2 in bite 1 in; slat screws #8 x 1-1/2 in bite 3/4 in into a 3-1/2 in rail with the tip 2-3/4 in inside the wood; end-brace screws are #8 x 2 in on purpose - bite 1-1/4 in with the tip stopping 1/4 in short of the leg's far face, and the plan names the 2-1/2 in substitution as a mistake-fix because it pokes through.
BEGINNER-FIRST, IN DEPTH: every term defined at first use (propagation bench, flat, slat, gap and pitch, rail, cleat, bearing, bite, end grain, spacer block, paver, shim, twist, GFCI, drip loop, heat mat), a practice-first stage proving the cleat joint, the spacers, and the load worksheet, 26 continuously numbered steps in 8 stages, 12 labelled diagrams placed at their steps, a stop-and-check after every stage (including cleat witness lines, the 72 in dry-lay, the twist test, the proof load, and the drainage test), mistake fixes (sideways sheeting water, ponding, a racked frame, an opened rail joint, rotting leg feet, poked-through brace screws, a misused heat mat), good/better materials (cedar vs clear cedar or redwood; coated vs 305 stainless screws - the upgrade that matters most in daily wet service; shims vs adjustable glides; bare cedar vs penetrating oil, with film finishes named as wrong for wet service), and sourcing with exactly what to order - including the lumber yield math (37 pieces at 30 in from thirteen 1x4 x 8 ft boards; legs and rails from six 2x4 x 8 ft) - with costs labelled estimates totalling $245-$385 in cedar, or about $135-$205 on the ground-contact treated budget path. Heat mats and humidity domes are covered as use notes for bought plug-in equipment only: one mat on one rigid flat-sized tray, GFCI outlet TEST-proved, cord off the bench end with a drip loop - the plan contains no wiring instructions.
You receive: the PDF plan only (digital download, no physical product ships) with cut list, materials list, full two-way verification section, and final completion checklist. Full build plans and material list in the TheWorkshopBlueprint website store at theworkshopblueprint.shop.
