TheWorkshopBlueprint logo THEWORKSHOPBLUEPRINTDIY BUILDING PLANS
← All plans

Goat Kidding Pen Panel Set Plan - Modular 5x5 ft Barn Pen, Kid-Safe Solid Panels

Goat Kidding Pen Panel Set Plan - Modular 5x5 ft Barn Pen, Kid-Safe Solid Panels plan cover
$12.95 Buy Now

Not a standard off-grid kit - top-of-the-line, above and beyond the old style - safer by design, and every claim below names a real feature drawn into the plan itself.

THE BUILD: a modular goat kidding pen panel set forming a 60 x 60 in (5 x 5 ft) pen, 36 in high, open at the top, for indoor or barn use. Four flat panels - a 60 in back panel, two 55-1/2 in side panels, and a front of a 35-1/2 in fixed section plus a 24 in gate in a 24-1/2 in opening - bolt to four corner posts and unbolt to stack flat for storage. Each panel is a solid 3/4 in plywood skin with 2x4 battens on the outside only, so the inside is one smooth, gap-free surface.

WHAT THIS IS - AND IS NOT: this is a small indoor/barn kidding pen for ONE doe and her newborn kids, for a short kidding stay only. It is not the Chicken Run Panel Set (an outdoor wire run for poultry - wire is exactly what this pen avoids) and it is not the Three-Sided Goat Shelter (a permanent outdoor herd shelter). This plan makes NO health or birthing claims of any kind - it builds an enclosure only.

SAFER BY DESIGN - THE KIDDING-PEN FAILURES ARE DESIGNED AGAINST: (1) HEAD-TRAP GAPS are designed out - the plan states the standard livestock gap guidance honestly as guidance, not certification (an opening is safe only if a kid head cannot enter it, or can withdraw freely), then holds every interior opening to 1/4 in or less against a printed 1-3/4 in design limit, gauged with a shop-made block in a full audit step. There is no wire and no slat slot anywhere in the pen. (2) SHARP FASTENER POINTS INSIDE are designed out - all 85 skin screws are 2 in screws driven from outside through 1-1/2 in battens, biting 1/2 in into the 3/4 in skin and stopping 1/4 in short of the inside face, and a gated palm-snag sweep of every inside surface must pass before any animal goes in. (3) CORNERS THAT PULL APART are answered with through-bolts only - sixteen 3/8 x 4-1/2 in carriage bolts, smooth domed heads inside, washers and nuts outside, two per panel end; rated livestock panel clips at the same full count are the stated alternative. Screws and nails never hold a corner.

EVERY MEASUREMENT VERIFIED TWO WAYS: pen footprint by panel sum (side skin 55-1/2 + 2-1/4 + 2-1/4 panel stacks = 60 in; front and back 60 in) and by diagonal (sqrt(60 x 60 + 60 x 60) = 84.85 in, taped 84-7/8 in, both diagonals matched in the field); panel height by the 36 in skin and post cuts and by batten stack (3-1/2 + 29 + 3-1/2 = 36 in); gate opening by front sum (35-1/2 + 24-1/2 = 60 in) and by subtraction (60 - 35-1/2 = 24-1/2 in), closing again as gate 24 in plus two 1/4 in clearances. Every fastener is reach-checked and every load path is traced skin to battens to bolts to posts to floor.

BEGINNER-FIRST, IN DEPTH: every term defined at first use (kidding pen, batten, through-bolted, carriage bolt, bite, palm-snag sweep, gap gauge), a practice-first stage proving the no-through screw joint split open, the gap gauge, and a bolted test corner, 30 continuously numbered steps in 6 stages, 12 labelled diagrams placed at their steps, a stop-and-check after every stage, mistake fixes (a gauge-wide joint, a through screw point, a spinning bolt, a binding gate, a rocking pen, a post-audit gap, bedding in the gate swing, a split batten), a good/better materials path (galvanized or stainless corner hardware, sanded skins, hardwood gate battens, rated panel clips), and sourcing with all prices labelled ESTIMATE.

You receive: the PDF plan only (digital download, no physical product ships) with cut lists, materials list, full two-way verification section, and final completion checklist. Full build plans and material list in the TheWorkshopBlueprint website store at theworkshopblueprint.shop.

Finished size Pen 60 x 60 in outside (5 x 5 ft), 36 in high, open top; back panel 60 in, side panels 55-1/2 in, front fixed section 35-1/2 in, gate 24 x 35 in in a 24-1/2 in opening
Materials estimate $360-$520 (estimate: four sheets 3/4 in plywood, 2x4 battens and posts, 85 screws, 16 carriage bolts with washers and nuts, T-hinges and latch; better path with galvanized/stainless hardware at the top of the range)
Skill level Beginner

See more plans in Coops & Animal