TheWorkshopBlueprint logo THEWORKSHOPBLUEPRINTDIY BUILDING PLANS
← All plans

Goat Hay Feeder Plan

Goat Hay Feeder Plan plan cover
$11.95 Buy Now

Build a roofed goat hay feeder, 72 x 36 inches, that keeps hay dry, keeps goats out of the hay, and catches dropped hay in a manger tray instead of the mud. It feeds from both long sides through a truncated-V slatted rack, under a shingled single-slope roof (6 inch drop, 6 inch overhangs) carried on four posts set on pavers.

HEAD SAFETY, STATED PLAINLY: the clear gap between slats is exactly 3 inches - a standard adult goat's muzzle pulls hay through, but a skull 4-1/2 inches or wider cannot pass, so the head never enters the rack and cannot trap. This feeder suits standard-size ADULT goats only (roughly 80 lb and up, skull at least 4-1/2 inches at its widest, polled or disbudded). It is NOT for kids, young stock, miniature or pygmy goats, or horned goats, and the plan says so up front, with a 4-1/2 inch skull-gauge test you run on scrap and again on the finished rack. The rack ends are closed solid, and no board spacing anywhere falls in the head-trap range.

CAPACITY, HONESTLY: the rack section is a trapezoid (26 inch top, 6 inch bottom, 20 inch deep) x 63-1/2 inches inside = 11.76 cu ft, worked two ways in the plan. At loose-hay density and a realistic 75% fill that is about 35 lb - 8 to 9 flakes, roughly 3/4 of a small square bale. Not a whole bale, and the plan shows the math instead of claiming one.

EVERY LOAD RESTS ON SOMETHING: rafters on top plates on posts on pavers; tray floor on support rails on stretchers; rack top rails on corbel blocks at the posts; rack bottom rails on two trestles standing on the tray floor. All math is worked two ways: footprint chains (72 - 3.5 - 3.5 = 65; tray floor 62 from the full chain), the height chain from the paver datum (tray rim 20-1/2, rack 28 to 48), slat slope sqrt(20 squared + 8.5 squared) = 22 inch slats, rafter length 49 inches, the slat chain 1.5 + 35 + 27 + 1.5 = 65, every fastener's bite, and bearing checks throughout - nothing load-bearing merely kisses.

This is a beginner-first plan, not a one-page cut list. Every term is defined at first use (corbel block, trestle, clear gap, truncated V, flake), you practice the four critical skills on scrap first - the 3 inch spacing block and skull gauge, a corbel block, angled slat ends from a full-size slope drawing, and the tray corner - and every stage has its own labeled diagrams (12 illustrations), a stop-and-check checkpoint, fixes for the common mistakes, and a final checklist.

You receive: a PDF plan with cut list, materials list, tool list, 32 continuously numbered steps, 12 diagram figures, full measurement verification (dimensions, slat safety, roof, hay capacity, every fastener's bite, and bearing), mistake fixes, and a final checklist, plus a materials estimate of $190-$260.

DIGITAL DOWNLOAD: this listing is for the PDF building plan only. No physical product will be shipped. Print it or build from a tablet in the yard.

Full build plans and material list in the TheWorkshopBlueprint Etsy shop.

Finished size Feeder 72 in long x 36 in wide footprint; roof about 77-3/4 in at the high front eave, 71-3/4 in at the back, roof plan coverage 84 x 48 in; rack 26 in top / 6 in bottom / 20 in deep, about 63-1/2 in inside; tray rim 20-1/2 in, tray depth 4-3/4 in
Materials estimate $190-$260 (3x 4x4x8ft treated posts, 12x 2x4x8ft, 2x 2x6x8ft, 7x 1x4x8ft, 1x 3/4in plywood sheet, 2x 1/2in plywood sheets, roofing felt, 1 bundle shingles, roofing nails, 10 rafter ties, 4 pavers, exterior screws, paint/sealer)
Skill level Beginner

See more plans in Coops & Animal