TheWorkshopBlueprint logo THEWORKSHOPBLUEPRINTDIY BUILDING PLANS
← All plans

Convertible Bench-to-Picnic-Table Plan

Convertible Bench-to-Picnic-Table Plan plan cover
$13.95 Buy Now

Not a standard off-grid kit - top-of-the-line, above and beyond the old style - safer by design, and every claim below names a real feature drawn into the plan itself.

THE BUILD: one convertible unit, 72 in long, that is two pieces of furniture in one footprint. As a BENCH: a fixed seat 15-1/4 in deep with its top at 17-3/4 in and a tall back reclined 12 degrees past vertical, top edge at 42 in. Flip the top with the two-hand conversion procedure and it becomes a TABLE: the back panel swings 78 degrees down and back to a level 22 in wide tabletop at 28-3/4 in over the same fixed seat, seating 4 as a table - four 18 in places along the 72 in side, and the plan shows that math (4 x 18 = 72). Build a second unit, set the pair back to back, and you have a full picnic table about 44 in wide. NOT the classic 8 ft picnic table in this same store: that one is a fixed 96 in table, always a table. This one converts - a bench on the porch all week, a table for four when you need it.

SAFER BY DESIGN - THE FOUR WAYS CONVERTIBLES FAIL, DESIGNED AGAINST IN THE OPEN: (1) PINCH AND CRUSH AT THE PIVOT - the plan specs a 3/4 in minimum pinch gap at every point of the swing, proves it on a full-size template before any real part is drilled, re-checks it on the finished unit with a spacer block through three full swings, and prints a two-hand conversion procedure (hands on the panel top edge only, unit empty, pins in at all three frames before anyone sits). The design clearance at the seat corner is 2.02 in by coordinates - nearly three times the spec. (2) TIPPING IN BENCH MODE - the sled feet are a full 39 in front to back, and the plan works the lean case in the open: a 50 lb horizontal lean at the 42 in back top makes about 2,100 in-lb of overturning moment against about 6,525 in-lb of restoring moment from a 225 lb sitter - about 3 to 1 - and in table mode the tabletop far edge and its 50 lb edge load fall 2 in INSIDE the footprint. (3) PIVOT BOLT SHEAR AND WEAR - each of the three pivots is a 3/8 x 4 in Grade 5 bolt (stack worked in the plan: 3.47 in of upright, washers, arm and nut, so the 4 in bolt finishes with about 1/2 in of thread past the nyloc nut), worst-case design shear about 165 lb per pivot against a conservative capacity over 3,000 lb - margin over 18 to 1 - with template-drilled matched pivot pairs and washers on both faces against hole wear. (4) GEOMETRY COPIED FROM A PHOTO - this plan's pivot geometry is verified TWO independent ways and must agree both ways: by coordinates (pivot at X -2, Y 24-1/2; panel edges 5 in and 17 in from the pivot along the panel; distances pivot-to-edge 6.56 in and 17.52 in and edge-to-edge 22 in in BOTH modes; tabletop level at 28-3/4 in, back top at 42 in) and by a full-size template swing check the builder performs in Step 1.

LOADS STATED PLAINLY: seat 250 lb per person position across two 33-3/4 in bays on three cross rails; tabletop 200 lb distributed plus a 50 lb point load at the far edge; back 50 lb horizontal lean load at the top. Every slat bears on a dimensioned support - seat slats on three cross rails, panel slats on three pivot arms - and every screw is bite-checked in the plan (seat and panel screws 1.5 in of bite, stop-block screws 1.0 in in their position-only role).

BEGINNER-FIRST, IN DEPTH: every term defined at first use (pivot, datum, footprint, bearing, bite, shear, nyloc nut, locking pin, template, stop block), a practice-first stage proving the pivot template, the pivot feel, and both slat sums on scrap, 24 continuously numbered steps in 5 stages, 12 labeled diagrams placed at their steps including both modes and the conversion motion itself, a stop-and-check after every stage, mistake fixes (unlevel tabletop, pinch-block contact, pivot slop, foot lift, a pin that will not pass, a binding swing), good/better materials (pine vs cedar/oak arms, zinc vs stainless pivot hardware, clevis pins vs ball-lock pins), and sourcing with exactly what to order and costs labeled estimates totaling $230-$330.

You receive: the PDF plan only (digital download, no physical product ships) with cut list, materials list, full two-way verification section, conversion and load-test stages, and final checklist. Full build plans and material list in the TheWorkshopBlueprint website store at theworkshopblueprint.shop.

Finished size 72 in long; bench mode: seat 15-1/4 in deep, top at 17-3/4 in, back top at 42 in, 12-degree recline; table mode: tabletop 22 in wide, top at 28-3/4 in, seats 4 along the 72 in side; footprint 39 in front to back
Materials estimate $230-$330 (estimate: pine/fir 2x6 and 2x4 lumber, Grade 5 pivot bolts with nyloc nuts, locking pins, exterior screws and finish)
Skill level Beginner

See more plans in Furniture