TheWorkshopBlueprint logo THEWORKSHOPBLUEPRINTDIY BUILDING PLANS
← All plans

Hand-Crank Compost Sifter Trommel Plan

Hand-Crank Compost Sifter Trommel Plan plan cover
$11.95 Buy Now

Build a hand-crank compost sifter trommel: a 36 inch long x 24 inch diameter rotating drum screen on a tilted wooden frame. Shovel rough compost into the high end, turn the crank, and finished compost rains through the 1/2 inch mesh into a bin below while sticks and stones walk down the drum and drop out the low end.

A CAGE, NOT A TUBE: three plywood rings (24 inch OD x 21 inch ID) carry six longitudinal slats, and the hardware cloth is screwed to the slats from inside - when the mesh wears years from now, you replace one 62 inch wrap with hand tools instead of rebuilding the drum. Mesh math is worked in the plan: the mesh circle is 19-1/2 inches in diameter, pi x 19.5 = 61.3 inches, plus a 3/4 inch seam overlap = a 62 inch cut from a standard 36 inch wide roll (the roll width IS the drum length).

REAL SHAFT, REAL BEARINGS: a 3/4 inch steel shaft (48 inches: 40 between bearings + 2 + 6 stick-out, checked two ways) drives the drum through cross-pinned hub blocks and turns in two pillow-block bearings. The load path is all bearing and compression: bearings rest ON end rails, end rails rest ON leg tops, legs stand on the ground. Design load 100 lb, about 25 lb per leg, computed two ways in the plan.

THE TILT DOES THE CONVEYING: axle heights are 40 inches (loading end) and 37 inches (exit end) - a 3 inch drop over the 40 inch bearing span, about 4.3 degrees, built entirely into the leg lengths (35-1/4 vs 32-1/4 inch legs). The plan explains why steeper races material through unsifted and shallower stalls it.

SAFE BY DESIGN AND BY RULE: maximum batch 50 lb (about three heaped buckets, with the drum-volume math shown), all mesh edges folded so cut wires are trapped (you prove the fold with a bare-palm test on scrap first), 2 inch end gaps and a 10 inch crank radius with the hand force worked out (about 20 lb at the worst point of a full-batch turn).

This is a beginner-first plan, not a one-page cut list. Every term is defined at first use (trommel, overs, fines, pillow-block bearing, hub, shaft collar), you practice the four critical skills on scrap first - the string-compass ring, the mesh edge fold, the centered shaft cross hole, and the radial slat screw - and every stage has labeled diagrams (12 illustrations, one at every technique step), a stop-and-check checkpoint, fixes for the common mistakes, and a final checklist.

You receive: a PDF plan with cut list, materials list, tool list, 32 continuously numbered steps, 12 diagram figures, full measurement verification (drum geometry, tilt, frame heights and clearances, loads computed two ways, every fastener's bite, and bearing), mistake fixes, and a final checklist, plus a materials estimate of $120-$165.

DIGITAL DOWNLOAD: this listing is for the PDF building plan only. No physical product will be shipped. Print it or build from a tablet in the garden.

Full build plans and material list in the TheWorkshopBlueprint website store at theworkshopblueprint.shop.

Finished size Drum 36 in long x 24 in outside diameter (mesh circle 19-1/2 in); frame about 44 in long x 29 in wide; axle heights 40 in high end and 37 in low end (3 in drop over 40 in, about 4.3 degrees); fines bin up to 22 in tall fits underneath
Materials estimate $120-$165 (3/4in plywood sheet for 3 rings, 4x 2x4x8ft, 3x 1x3x8ft, 1x 1x2x8ft, 6ft of 1/2in hardware cloth 36in wide, 3/4in x 48in steel shaft, 2 pillow-block bearings, 4 shaft collars, screws, bolts, finish)
Skill level Beginner

See more plans in Garden